A few years ago while browsing the Halted Anniversary Sale, I came across a 4 bay 5.25" SCSI drive case for something really cheap (I think $35). I can't pass up a deal like this so I snagged it. Well it sat around for a long time, past the point of me giving up on SCSI. I had replaced my 3 36GB SCSI drives with 2 80GB IDE drives and never wanted to go back. So it sat. While performing the SparcStation ITX hack, I discovered that firewire to IDE bridgeboards could be had in the $50 to $80 range. After using one there I started a little thread in the back of my mind about what other nefarious uses I could find for these little gems. Then one day I saw an ad for a full height 5.25" box that held 3 3.5" hard drives. Suddenly inspiration struck me like a bolt of lightning, and in true Dr. Bob fashion, I took it to an extreme.

The largest drive available at the time I started this hack was the Maxtor 200GB.
What do you think?

Here's how I did it:
1. Start with the empty case.


2. The original case fans were very noisy. In addition to that, the fan grilles cause lots of turbulence noise. So I cut them all out and replaced them with PanaFlow fluid bearing fans and wire grilles. I had to make custom power cable harnesses for these fans as well


3. As long as I was replacing noisy fans, I replaced the fans in the drive carriers with think PanaFlow FDB fans. I threw their grilles out altogether as they operate with their doors closed and the grille is, well, pointless.


4. Next I downloaded the art work for the firewire logo from Apple's web site. I printed out one that would fit and glued it to the boring beige top case. Black indicated material to be removed. First I drilled pilot holes to get the tool bits in. Then I started cutting to remove the big chunks, then I cut closer to the edges with my dremel tool, and finally filed it smooth with my half round bastard (not shown here). Those that know the joke are now snickering.


5. After this the whole case was sanded and painted with Krylon Fusion Burgundy Red. This paint takes 7 days to fully polymerize so I set it aside and focused on the electronics. I also bought a hunk of clear acrylic from TAP plastics and a 30mm round for the center of the logo.


6. OK I've got a firewire hub that mounts in the same hole as the old Centronics connector did (firewire depot), and 3 dual drive FireWire to IDE controller cards. Plus I need to supply power and route the cables for data and the LED's. I decided to mount them on the empty panels between the back of the drives and the back panel. First I had to measure the card for the stand off. Never leave home without your trusty calipers.


7. Now the cards can be mounted on my 3/4" standoffs and 4/40 screws. This project would be impossible without round IDE cables. The powered hub is visible in the lower left of the 1st picture.


8. This might look like a chaotic mess to you, but it's actually a carefully choreographed symphony of cable. The truth is, it's the only way it would all fit.


9. This is glue. Strong stuff.


10. When the front was dry, I hit it with some 3M Imperial Hand Glaze. That made it nice and shiny. Mmmmmm Shiny. (droooool)


11. Now it's time to get silly. I installed 2 6" and 2 12" tri-color cold cathode lamps. These will really spice up my life. After messing with EL wire, I have decided that it's not bright enough to be worthwhile for almost any use. CCFL lamps however are bright enough to be seen in any lighting conditions including camera flash. EL wire is only visible in low light. CCFL lamps also last longer.


12. Like EL wire, cold cathodes require a high voltage inverter.


13. Finally I mounted some LED's in the front connected to the busy signal outputs on the firewire controller cards. I may at a later date remove this metal grill to improve the lighting and airflow.


All done. Here are some beauty shots:







Please visit my archive of art work photos for this project. Click on any picture for a very high resolution photo. Some of these really move me.

Tech Specs:
  1. Firewire 400 (sustained transfer rate of 35MB/s, max for firewire 400)
  2. Oxford 911 chipsets
  3. 6 Maxtor 200 gig ATA 133 hard drives
  4. 4 cold cathode lamps with a combined output of 12 watts
  5. 16 LED's
  6. Powered firewire hub

No pages or images anywhere within my site may be linked to on another web page without my express written consent.
Copyright September 22 2003 Bobby Kinstle. All rights reserved.